concrete27

Can hot concrete and asphalt?

Can hot concrete and asphalt? A concrete driveway will increase property values in most areas, that is, if it is done properly. … Never place concrete directly on a polyethylene vapor barrier or bone-dry subgrade. The subgrade should be damp, with no standing water.

How thick are walls in concrete houses? Solid precast concrete walls should have a typical thickness of 4-12 inches. Thin-shell walls should be 5-12 inches thick, including 1-4 inches of insulation. Sandwich precast concrete walls should also be 5-12 inches thick, including the 1-4 inch insulation.

How thick should an exterior concrete wall be? The thickness of exterior residential walls when using ICFs depends on several factors. Standard ICF external walls need six inches of concrete. However, areas susceptible to high winds require concrete thickness of at least 8 inches.

How thick should residential walls be? When it comes to standard building materials, masonry walls tend to be the thickest, and the maximum recommended thickness for walls up to 70 feet high is 12 inches. Add an extra 4 inches for each additional 70 feet in height. Any thickness greater than this, regardless of the material, is excessive.

Can hot concrete and asphalt? – Related Questions

Can concrete work be done in the winter?

Make no mistake, pouring concrete during the winter can be done, but it will come with additional expenses to ensure success. The site that the concrete is to be poured on must not, itself, be frozen, so extra preparations must be made to recreate summer-like conditions during the winter before pouring can take place.

How do you repair cracks in a concrete birdbath?

Birdbaths have a tendency to crack after going through a freeze and thaw cycle. Small hairline cracks can be sealed with a waterproofing concrete sealer or epoxy, and larger cracks can be filled with a polyester resin. Pour half of your cleaner into your birdbath and use your scrub brush to clean the entire bowl area.

Are there self drilling concrete screws?

Self-tapping screws are concrete screws that tap threads into the base material such as concrete, brick or block. … There are many brand names of concrete screws on the market today. The original self-tapping and the most widely recognized one is called Tapcon, which is derived from Tapping Concrete.

Why steel is used as reinforcement in concrete?

The steel provides all the tensile strength where concrete is in tension, as in beams and slabs; it supplements the compressive strength of concrete in columns and walls; and it provides extra shear strength over and above that of concrete in beams. …

How to fix crumbling concrete sidewalk?

The steel provides all the tensile strength where concrete is in tension, as in beams and slabs; it supplements the compressive strength of concrete in columns and walls; and it provides extra shear strength over and above that of concrete in beams. …

How much to have a concrete driveway poured?

Most concrete driveway installation costs between $1,800 and $6,000 or $4 to $15 per square foot. The average is just above $3,000 or $6 per square foot.

How big of a concrete pad for generator?

The depth of the generator should be 125 percent of the unit weight when fuel is included. For instance, a generator that weighs 10,000 pounds should have a concrete pad of 12,500 pounds.

Can i put brick pavers over concrete?

Fortunately, you can put pavers directly over existing concrete. It’s a common practice and a great way to upgrade your concrete surfaces. While mortar is preferable when installing pavers, it’s possible to put in the pavers without mortar (although it puts you at risk of drainage issues and cracking).

Can i pour concrete over tile shower floor?

Generally speaking, it is possible to lay concrete over a tile floor. As long as the tile is in good condition, sound, and there are not any problems with what is under the tile, then the concrete can be laid successfully. Putting down concrete overlayment is a rather tedious process.

How much should concrete work cost building?

A concrete slab costs between $4.34 and $7.73 per square foot, with an average cost of $6.60 per square foot. The national average cost of a concrete slab is $6.60 per square foot for materials and labor. Most homeowners can expect to pay between $4.34 and $7.73 per square foot for concrete installation.

Can t drill into concrete?

Drilling into concrete is difficult because concrete is dense, is hard, and has embedded aggregate stones that can be obstacles to the drill bit. Drilling can quickly dull drill bits. When the bit encounters aggregate, the bit drags even more.

Can you concrete over laminate countertops?

From what I’ve read, a concrete skim-coat would transform my laminate without having to remove or rebuild the counters. It’s applied straight on top of the laminate in troweled-on layers. And it is inexpensive. … The product I used is Henry brand Feather Finish concrete Underlayment Patch and Skimcoat.

How do you decrease the strength of concrete?

The presence of air voids in concrete greatly reduces its strength . Approximately 5 % of air voids can reduce the strength by 30 to 40 %. As we can see in the above chart, even at the same water/cement ratio strength is different with different compaction accuracies.

How concrete mixer works?

A typical concrete mixer uses a revolving drum to mix the components. For smaller volume works, portable concrete mixers are often used so that the concrete can be made at the construction site, giving the workers ample time to use the concrete before it hardens. An alternative to a machine is mixing concrete by hand.

How cutting concrete 12 inches?

A typical concrete mixer uses a revolving drum to mix the components. For smaller volume works, portable concrete mixers are often used so that the concrete can be made at the construction site, giving the workers ample time to use the concrete before it hardens. An alternative to a machine is mixing concrete by hand.

How to lay linoleum on concrete floor?

Glue is applied to the entire underside of the linoleum. And to do so, you fold the linoleum back on itself and then apply the glue to the concrete directly. You then place the linoleum on the wet glue and press it firmly into place.

Can you pour concrete over existing concrete driveway?

You can put new concrete over old concrete. However, unresolved issues with your old concrete, such as cracks or frost heaves, will carry over to your new concrete if not taken care of. In addition, you must pour it at least 2 inches thick.

What causes black algae on concrete driveways?

Black algae commonly crop up on concrete driveways in areas with high levels of humidity and heavy rainfall. While black algae won’t damage concrete driveways, they can be an awful eyesore. Small colonies quickly spread to cover large areas. Attack even small black algae colonies as soon as you see them.

Are concrete floors soundproof?

A good percentage of floors are made out of concrete. This type of floor, in particular, has a high level of mass, which makes it one of the best soundproofing materials as far as airborne noise is concerned.

How much concrete in 1 yard?

How much concrete is in a yard? Concrete volume is measured in cubic yards. When poured on a perfectly level surface, one cubic yard will cover 27 square feet at one foot thick.

How to secure plywood to concrete floor?

How much concrete is in a yard? Concrete volume is measured in cubic yards. When poured on a perfectly level surface, one cubic yard will cover 27 square feet at one foot thick.

Leave a Comment

Your email address will not be published. Required fields are marked *