Can i drill into hollowcore concrete slab? You can partially drill the slab and remove the bulk of the core so only the last remnants actually fall through. Wet drilling will mean you will need water protection, polythene sheeting to direct the waste slurry to a bin or tub.
Can you drill into prestressed concrete? Typically, one normally doesn’t drill through a prestressed precast concrete to attach it to anything, unless you know EXACTLY where the prestressing wire strands are located within it.
Can I drill into my slab? It’s safe to drill into the slab and foundation, as long as it’s not big holes. And you don’t want two access holes/ slots coming in at a 90 degree angle to each other. The possible problems later on could be moisture ingress, and bug ingress.
Can you cut holes in precast concrete? Can a precast hollow-core concrete floor be cut? Any instructions to make this safer would be greatly appreciated. A: This type of floor can be cut, but you are wise to check into things before doing so. The best approach would be to contact the producer who supplied the floor for guidance.
Can i drill into hollowcore concrete slab? – Related Questions
What is pneumatic forming of hardened concrete?
The Pneumatic Forming of Hardened Concrete Construction Principle. ]. Air-space pneumatic formworks are placed inside a conventional formwork to leave a space in the concrete structure. Classical pneumatic formworks are inflated, and the concrete—most commonly sprayed concrete—is applied subsequently.
Can you apply concrete sealer over a wax finish?
Many concrete contractors recommend applying a mop-down wax or floor finish to your decorative concrete floor after you seal it. … Applying several coats of wax over the sealer coat helps to protect the sealer from wear and preserve your floor.
How to use concrete trowel?
Hold the trowel almost flat and swing it in large overlapping arcs while applying pressure. Float the concrete when you’re done grooving and edging (Photo 6). Floating removes the marks left by edging and brings the surface one step closer to a final finish.
What is poured block with concrete?
Hold the trowel almost flat and swing it in large overlapping arcs while applying pressure. Float the concrete when you’re done grooving and edging (Photo 6). Floating removes the marks left by edging and brings the surface one step closer to a final finish.
How to get grease spots off concrete?
Scrub with a paste – Use baking soda or powdered laundry detergent and water to dissolve the oil stain. Rinse with water. Wash with soap – Dish soap and a scrub brush are often effective on new oil spots. Rinse the concrete clean.
What is a 6 bag mix of concrete?
A six bag mix is a concrete mix that has six bags of portland cement in it. In general, the more bags of cement in a mix, the stronger the mix. Most mixes have 5 to 7 bags of cement. Some concrete contractors (usually the old timers) will order their concrete based on bags rather than psi.
Can you paint concrete with latex stain?
Pro tip: Don’t use oil-based paint or latex paints on your concrete patio, pool deck or driveway. They will peel, crack and don’t hold up well outdoors. Instead use a paint formulated specifically for use on concrete or masonry. These are often made with acrylics or epoxies.
Can i use cold patch on concrete?
It can be used on roads, highways, streets, airport pavements, parking lots, bridge and parking decks, sidewalks, walkways, and floors. No mixing, heating, or special installation equipment is required. STORAGE Pallets and bags of HP Concrete Cold Patch should be kept intact and stored under cover.
What property of concrete does the slump test determine?
The concrete slump test measures the consistency of fresh concrete before it sets. It is performed to check the workability of freshly made concrete, and therefore the ease with which concrete flows. It can also be used as an indicator of an improperly mixed batch.
Should i patch concrete before using self levelling compound?
It has to be cementitious . No , sealing the concrete may cause the leveling compound not to bond with the concrete.
What’s the best concrete countertop sealer?
The Polyaspartic 745 is one of the best and easiest concrete countertop coatings to use. Not only does it provide one of the most beautiful, high gloss finishes, but it is food safe and able to withstand harsh staining from acids like lemon and wine.
What will stain concrete?
If you want to stain old concrete, using a true acid stain is always the best option. Avoid “acrylic stains” as these are disguised paint and will also peel with time. Concrete Acid Stains are the only true stains with permanent results.
Why shrinkage test for concrete is important?
Concrete block shrinkage is an important phenomenon that causes most of the movement in concrete masonry. If care is not taken at the design stage, eventual damage is likely to occur.
How do i cover and exterior concrete block walls?
The simplest way to cover a cinder block wall is by using surface bonding cement to create a concrete finish. Concrete helps insulate the building and keep moisture out. It creates a smooth, finished surface you can leave as is or paint.
Why us homes are not made of concrete?
Originally Answered: Why aren’t more homes and buildings made of concrete in the U.S.? The biggest factors are cost and longevity. It is a more expensive material to build with compared to something like wood.
How to remove concrete from mixer?
Originally Answered: Why aren’t more homes and buildings made of concrete in the U.S.? The biggest factors are cost and longevity. It is a more expensive material to build with compared to something like wood.
How do you know concrete has frozen?
Formed concrete surfaces sometimes show ice-crystal imprints, indicating that fresh concrete was frozen. The absence of ice-crystal imprints is one indication that concrete hasn’t been damaged by freezing.
How to insulate concrete floor from cold?
When installing insulation on top of the concrete floor, the most common method of installation is as follows. Lay the damp proof membrane onto the concrete, followed by the insulation. Then lay moisture-resistant chipboard, or a concrete screed to the top, which can then be covered by the flooring to finish.
Can regular power drill be used on concrete?
You can drill holes in concrete with a regular drill. … You will need a bit more patience and a wider array of drill bits when using a regular drill, but the procedure is the same for drilling in concrete regardless if you use a regular drill or a hammer drill.
How long concrete dry cover with carpet?
Concrete takes 28 days to fully cure. While it is curing there is moisture escaping from the concrete in the form of vapor. Covering the concrete with glue and carpet before 28 days will increase the chances of the glue not bonding properly and the carpet having a damp, musty odor.
How to figure out square footage of concrete?
Measure the length and width that you’d like to cover. Multiply the length by the width to determine square footage. Convert the thickness from inches to feet. Multiply the thickness in feet by the square footage to determine cubic feet.