How close can my mantel be to fireplace? As a general rule, the mantel is placed about 12 inches above the fireplace opening. Then adding an inch to the distance for every inch that the mantel protrudes. So a mantel 6 inches deep, would be attached 18 inches above the firebox opening.
How far away should mantel be from fireplace? Most housing codes and the National Fire Protection Agency (NFPA) state that the bottom of the mantel must be at least 12” away from the top of the fireplace box. The main factor for distance will come down to the Face Height of your mantel.
How much space should be on the side of a fireplace? A 36″ or 42″ fireplace opening width is more common, but you need to assume about 18″ on each side for a typical non-combustible surround and wood mantel, 24″ on each side for something more grand. The same thing goes for stone on each side.
How high is too high for a fireplace mantel? If your mantel is too close to the flames, you risk catching the mantel and anything on or near it on fire. A mantel that is at least 12 inches above the opening of the fireplace should be high enough away from the flames to keep you, your family, and your house safe.
How close can my mantel be to fireplace? – Related Questions
Can i burn pine cones in my fireplace?
Yes, pine cones can be burned in wood stoves or fireplaces. But be sure they are dry to avoid popping and extra creosote buildup. Dry pine cones make great kindling and fire starters.
Can you put new tile over old tile on fireplace?
Nowadays, it is quite possible to tile over the old tile and avoid the time and money of cleanup and backerboard installation. The average do-it-yourself homeowner can cover their old tile fireplace surround with new tile in one to two days, depending on the size and scope of the project.
Can i burn cardboard boxes in my fireplace?
Cardboard. While it’s easy to ignite and may seem like a good way to help get a fire started, burning cardboard can be dangerous. … If a burning piece of cardboard escapes your fireplace, it could quickly start a fire on nearby combustibles. Or, more commonly, they can float up into your chimney and cause a chimney fire.
Does a gas fireplace pilot light stay on?
Most gas fireplaces rely on a “continuous pilot light,” a type of pilot that remains lit so long as gas is flowing to the unit. Some newer, more energy-efficient models rely on an electronic ignition that only lights the pilot when the fireplace itself is turned on.
How to build a fire in a fireplace with hardwood?
Set up logs, kindling, and tinder using the upside-down fire method. Light the kindling; be on the watch for smoke spillage. Add seasoned wood logs, as the fire consumes the firewood. Keep watch of the fireplace (and don’t forget to enjoy it)!
Can i paint a fireplace screen?
Start spraying off to one side of fire screen, then move across and past it in an even stroke. Do not stop moving. Keep going back and forth until fire screen is covered in a thin coat of paint, making sure to cover top and side edges. Let paint dry completely.
How to decorate with a fireplace and tv?
To balance out the TV and fireplace front wall, bring in art and tall accents to fill out the vertical space. You want your fireplace and TV area to look well-rounded, so consider adding art above the fireplace and pulling in a tall plant or mirror to even things out. Think high contrast.
How to get an owl out of your fireplace?
The absolute most you can try to do is try to get the owl onto a pole of some sort to carry it outside, but calling a professional is still preferable. If your chimney is being used, then light a fire/ turn on the stove or furnace..get a little heat and smoke in there and the owl should leave on its own.
How to know fireplace is closed?
Stick your hand near the opening of the fireplace. If you feel air breeze against your hand, then it’s safe to say that the damper is open. If there’s a clear absence of a draft, then it’s closed.
Can you cement over a brick fireplace?
Smearing cement over old brick is a great way to makeover an old and dated fireplace without spending a lot of money! You can easily do this in your home, simply have a tile installer come out to float the brick with cement.
How to change a marble surround fireplace?
If you have a marble surround that is cracked or loose, the best way to redo it is to remove the old marble and install new tiles of marble or another material. Break off a section of the old marble, using a hammer and chisel, then pry off the rest with a pry bar inserted beneath the edges of each tile.
How to block a draft fireplace?
To stop a fireplace draft close the damper between fires, or use a form of draft stopper such as a chimney balloon or draft excluder if a fireplace doesn’t have a damper. The damper must be opened, or the draft stopper removed, before any fire.
How to clean soot from inside a fireplace?
To do this, create a paste of either baking soda or cream of tartar mixed with a small amount of water. Apply it to the remaining soot and let it sit for 5-10 minutes. Then scrub with a firm toothbrush or small scrub brush and rinse.
Can marble touch firebox around fireplace?
Aside from the actual firebox, marble is suitable for every part of a fireplace. Marble is heat and fire resistant and is safe for wood or gas fireplaces, so it is a sensible finish option. The stone is durable enough to withstand the abuse of fireplace tools and stacked firewood.
Can you install fireplace after house built?
Be assured that it is possible to add a fireplace to an existing home. … Fireplaces generally fall into one of three categories: gas, masonry, and zero-clearance (also known as prefabricated or manufactured fireplaces).
Can you add a remote to any gas fireplace?
Yes, you can add a remote to your gas log set after it’s been installed and the log set is already equipped with a millivolt valve. You may even be able to completely convert your gas log set to a remote control system with variable flame and thermostatic controls.
Do you have to clean a gas fireplace?
While gas fireplaces don’t produce creosote, they do still need annual cleaning. Both propane and natural gas are clean burning gas fuels, so they don’t produce the same byproducts as wood, but they can still produce buildup that needs to be cleaned away.
How to acid wash fireplace?
For standard red brick, tough to clean areas can be effectively cleaned using a mild acid wash. The most common product is muriatic acid. Dilute the muriatic acid in ten parts water to one of the acid, and apply it with a brush. Wear rubber gloves for added protection.
Can you plaster a brick fireplace?
Applying the plaster was EASY. However, what was not as easy was getting the fireplace prepped and ready for the application. In our case, the fireplace had deep grooves in between each brick. For the plaster to go on smooth, and not crack, the surface needs to be as smooth as possible.
How to clean brick fireplace soap baking soda?
Make a thin paste by mixing 3 tablespoons of dish soap to 1/2 cup baking soda. Spread it on brick, let sit for 10 minutes and then scrub off with a brush. Rinse with warm water.
How many fireplaces in biltmore?
Biltmore House was designed by architect Richard Morris Hunt and is America’s Largest Home® spanning 175,000 square feet, which is more than four acres of floor space. The 250-room French Renaissance chateau includes 35 bedrooms, 43 bathrooms, and 65 fireplaces.