How much does it cost to remove a gas fireplace? Before you call someone to start knocking down your mantle, read our guide to get an idea of how much this project will cost. On average, the cost to remove a gas fireplace is between $600 and $2,500, though the price will be higher if you want to remove the breast, stack, and chimney flue as well.
How do you remove a gas fireplace? The cost to remove a fireplace and chimney is $3,000 to $6,000, which includes demolishing the stack and breast, installing structural support, and repairing the walls, floor, and roof. A partial fireplace or chimney demolition costs $500 to $2,500 to remove everything below or above the roof-line.
How much does it cost to remove a fireplace? But losing a fireplace can affect a home’s appeal and possibly even its resale value, real estate pros say. A fireplace can particularly be viewed as a valuable amenity in colder climates, and removing one could even reduce the number of buyers drawn to a property, some agents say.
Does removing a fireplace decrease home value? Can I remove a gas fire myself? To be clear, you should never attempt to remove a gas fire yourself. It is a legal requirement that this job is completed by a Gas Safe Registered engineer. … The risks of tackling this as a DIY job include fire, and death through inhalation if you do not properly cap off the gas pipe.
How much does it cost to remove a gas fireplace? – Related Questions
How to remove a thermocouple gas fireplace?
The only tool you need to replace a thermocouple is a wrench. Turn off the gas supply to the gas valve. Use the wrench to unscrew the connector that holds the thermocouple to the gas valve, then unhook the probe from its clip and pull out the entire thermocouple assembly.
What to put on your fireplace?
For an easy fireplace mantel decorating idea, hang a mirror in the middle and a sconce on either side. Anchor the mantel with a larger vase in front of the mirror and fill in with smaller accessories, such as vases, candlesticks, and decorative objects. Pick up on colors and materials found elsewhere in the room.
How to sync valor fireplace remote?
When using your remote control, hold down the OFF and large flame buttons simultaneously. Once you hear the beep to start the activation sequence, the buttons on the remote can be released. Once the pilot light ignites, the flames will turn to full fire and remain in “Manual Mode”.
Do you have to vent a gas fireplace?
Traditional gas fireplaces, like their wood-burning cousins, require an exhaust flue (vent) to remove harmful fumes from the home. When possible, an existing chimney is used to run a new flue, but in a home without a chimney, the high cost to install venting can sideline the project permanently.
How to find out what kind of fireplace i have?
Each fireplace and insert has a rating plate which contains your model number and serial number. Gas and wood burning fireplaces have a rating plate in the control compartment area, under the smoke shield or on the firebox side column.
Can you use a fireplace with oxygen in the house?
Do NOT use oxygen within 10 feet of open flames, such as fireplaces, wood-burning stoves and gas stoves. Use caution when using electrical equipment. Do NOT use equipment with frayed cords or electrical shorts. They could cause a spark.
Can i stain fireplace hearth?
The only way to stain such a fireplace is with paintbrushes. A smaller, finer-tipped brush is best for around the edges of stones to keep the stain out of the grout; use a larger, flat brush for the center of stones. Stain is applied just like paint.
What is the fan on my fireplace for?
A fireplace blower is a fan mounted on the exterior of the fireplace or inside the unit but outside the firebox itself. It is used to circulate air around the unit’s hot exterior before pushing it back into the room. Fireplace fans help to circulate warm air and increase heat penetration into the room.
How to mortar a brick fireplace?
Place the edge of the trowel or putty knife into a mortar joint. Scrape mortar off the trowel or putty knife and push it into the joint with a tuck-point trowel. A tuck point trowel resembles a long, narrow chisel. Tap the tip of the tuck-point trowel through the mortar in the joint to pack the mortar deeper.
Can electric fireplaces sit on carpet?
Yes, it is safe to sit an electric fireplace on carpet or on top of a rug. In fact, electric fireplaces can safely be placed on top of any stable surface.
What to look for in an electric fireplace?
So, typically when shopping for an electric fireplace, you’ll want to look for lower wattage and a higher BTU rating. Because of their relatively low wattage, most electric fireplaces can run off of a standard 120 volt plug (about 1500 watts), making electric fireplaces much more efficient than wood burning fireplaces.
How large should your fireplace mantel shelf be?
Your mantel should be wider than your fireplace. Typically, a mantel should be a minimum of 3 inches past the firebox on each side. However, more can be better. The average mantel is approximately 6 inches wider than the fireplace on either side, and some can be even wider.
Can an lcd tv go above a fireplace?
The short answer is – yes. However, to ensure your television isn’t damaged from the heat, care must be taken to ensure heat generated by the fireplace is redirected away from television.
Can i convert my gas fireplace into wood burning?
Not all gas fireplaces can be turned into wood-burning fireplaces. Converting a fireplace to wood is only possible with fireplaces originally built for wood. A wood-burning fireplace must have the proper, safe chimney and venting system.
Can you add a gas fireplace to a home?
Direct vent gas fireplaces can be installed almost anywhere in in a home where natural gas or liquid propane is available. Installation is flexible due to zero clearance construction, which requires minimal space between the fireplace and wallboard or wood (combustible materials).
Do you need a permit for a fireplace?
y Install a wood stove, fireplace insert, pellet stove, or related venting. y Install, alter, or repair gas piping between the meter or LPG tank and an appliance, either indoors or outdoors.
How do scandinavian fireplaces work?
In contrast, Swedish stoves are substantial, built with shaped bricks with the joints between the bricks sealed with clay. … This means that the bricks themselves warm up quickly and retain the heat which then slowly radiates out to warm the room. The tiles also help retain heat but rarely get too hot to touch.
Do all fireplace doors have adjustable damper control?
Not all chimneys or flues have a damper. Open fireplaces can usually be found with damper located within the upper part of the firebox. It’s common to find a damper as part of an open fireplace, but in some cases there may be no damper at all.
How to adjust gas fireplace flame color?
By opening the damper to the fireplace, you are allowing proper ventilation. This will control the color of the flame. To adjust it so that the flames have an orange or yellow tip to them, lower the air input. You can do this by changing the damper or by closing the air shutter.
How to remove creosote from fireplace?
To do so, you will need to start a fire, apply the creosote remover and repeat the procedure twice a week for a month. Each month, check and remove debris and use a chimney brush to remove additional residue. You can also add special logs or creosote remover sticks into a well-stoked fire to remove this substance.
What channel is a fireplace on?
Go to channel 47 or 347 or press Video On Demand on your remote. Choose Local on Demand > Backgrounds > Fireplace.