How to attach hardwood floor to concrete? Lay 6-mil polyethylene sheeting over the concrete to minimize moisture migration from the concrete up into the wood flooring. Then fasten 3/4-in. treated plywood to the concrete with concrete screws spaced every 16 in. Alternatively, screw rows of treated 1x4s to the concrete 16 in.
Can you install hardwood directly on concrete? If you have a concrete slab main floor or basement, you may be wondering if it’s possible to install hardwood flooring directly on top of the concrete. The short answer is yes.
Do you need underlay for solid wood flooring on concrete? It is important to mention that you do not need a wood floor underlay when you have a solid hardwood floor and that’s because it is not stable, hence it has to be installed mechanically to the concrete subfloor.
Can you put flooring directly on concrete? Laminate flooring can be installed over concrete, wood or carpet subfloor or other surfaces. Installation of good quality underlayment is highly recommended. Installing underlayment is easy but it has to be done precise to avoid any tears.
How to attach hardwood floor to concrete? – Related Questions
What humidity for hardwood floors?
The National Wood Floor Association (NWFA) states that normal relative humidity levels should range between 30%-50% to ensure successful long-term performance of your wood flooring.
How to clean pet stains on hardwood floors?
Mix one cup of vinegar into a warm water-filled bucket and the add some drops of grapefruit oil to the solution to get rid of the odor. Scrub the floor with this safe cleaning solution, concentrating on the most prominent spots. As you scrub, the odor and stains should be disappearing.
Is bona safe for engineered hardwood floors?
The BONA spray is super effective and a safe way to clean engineered wood floors (and is great for solid hardwood too)!
Why is bruce the best hardwood cleaner?
Bruce hardwood and laminate floor cleaner is a unique cleaner that lifts soil from the surface of the urethane finish without leaving a film. Its ready-to-use formula is great for spot and routine cleaning of all no-wax hardwood and laminate floors. No rinsing required and it leaves no dulling film.
How to tell if i have hardwood under carpet?
Look for any floor vent you can find, and carefully pull it up to remove it. They are rarely secured down in any way, so they’re easy to take out. The carpet won’t be tacked down around the edge of the vent opening, so you’ll be able to easily pull the carpet and pad up just enough to see what is underneath.
How to get carpet padding off hardwood floors?
Use a mix of warm water and dish soap to loosen any glue holding the carpet padding into place. For stubborn sections, try using a mix of vinegar and water or paint thinner and water to loosen the glue. If you want to avoid refinishing the floors, opt for an acrylic-based paint remover instead of paint thinner.
How to clean hardwood floors before lemon oil?
Clean the floor thoroughly before applying lemon oil. Sweep or vacuum the dust away, and wipe away grime with a damp rag. If the floor needs extra cleaning, mix an ounce of dish soap in a gallon of warm water and wipe down the floor with a rag; then dry it thoroughly. Don’t leave any water standing on the wood.
How long does it take to replace carpet with hardwood?
Typically, installation of hardwood floor takes anywhere from 1 to 3 days. The average job size ranges from 1000 to 5000 square feet. A two-person team of installers is typically able to complete 750 to 1000 square feet of flooring each day.
How to remove wood polish from hardwood floors?
Combine some dish liquid in water to make suds, skim the suds off the surface of the water with a cloth and wipe the suds onto the polished area. Continue washing the surface with the sudsy water until the polish is gone. Wipe the area with a dry cloth to remove the excess liquid afterward.
How to determine which way to run hardwood flooring?
Wood floors should always be laid perpendicular to floor joists—across rather that in between them. This will make the floors structurally sound and will help prevent the planks from separating, sagging or buckling. So, there is no right or wrong way to lay your wood flooring.
What is hardwood mulch made of?
Hardwood mulches come from chipped or shredded branches or small trees, although old construction wood, pallets and utility poles also find their way into mulch. Hardwood mulch becomes alkaline as it breaks down, benefiting all but those plants that need a lot of acid.
How to clean and maintain old hardwood floors?
Sweeping on a daily basis is the best way to maintain your hardwood floors. Sweeping or mopping removes dirt, dust, pet hair, debris and other harmful substances that can worsen the condition of your damaged floors. During the sweeping or mopping process, use a soft bristle broom, dust-mop or a microfiber mop.
How to screw into hardwood?
Place a drill bit in the electric drill’s chuck and tighten the chuck. The bit should be the same diameter as the screw’s shaft. Drill a pilot hole through the board and part way into the stud or other board. Remove the drill bit and replace it with a Phillips or screw driver bit.
Are engineered hardwood floors safe?
The most common type of engineered hardwood floor has a plywood base. The core is made of plywood and a top layer of real wood is glued on. … In general this type of engineered wood flooring is safe for almost everyone including most people with chemical sensitivities.
How to clean an area rug on hardwood floor?
Vacuum or dry mop the hardwood floor to remove any dirt and grit that could cause scratches. Lay down and secure thick plastic sheeting to protect the hardwood floors while the rug is wet. Clean the rug using carpet shampoo or a carpet steamer, and do not replace the rug until it is thoroughly dry.
What sander to use to refinish hardwood floors?
Random orbital sanders are the best choice for do-it-yourself hardwood floor refinishing. They take longer to remove old finishes than drum sanders, but they do not require a lot of experience to use and are less likely to damage your wood floor.
How many coats of water based polyurethane on hardwood floors?
You are best off using 3 coats of water based polyurethane for the best results. And, this is is especially important on the 1st floor of your home and heavy traffic areas (e.g. kitchen, entryway, family room).
What kind of flooring can you put over hardwood?
Laminate flooring can be installed directly over hardwood, often with no preparation necessary. If your laminate has a built-in underlayer, you may install it right on top of the hardwood.
Can you have two different color hardwood floors?
Put simply, the answer to the question do wood floors have to match room to room, is entirely one of personal choice. You can choose to have different flooring in each room if that works for you, but synergy and flow from selecting one central flooring material can look wonderful too.
How long should hardwood sit before install?
Wood flooring material needs to acclimate (adjust) to the moisture and temperature conditions of the installation environment for at least three days (72 hours) before it can be installed.
Why does my hardwood floors have gaps?
Gaps in wood floors are normal and occur when the wood loses its moisture content. … Often gapping can result with flooring installed during periods of higher humidity. Months later, usually during the heating season, those gaps start to show up. The good news is that they usually close back up.