How far out should a fireplace mantel be? Mantel Height: We recommend installing the mantel 4.5′ from the floor. This allows room for stockings during the holidays. Most housing codes and the National Fire Protection Agency (NFPA) state that the bottom of the mantel must be at least 12” away from the top of the fireplace box.
How far should a fireplace mantel stick out? The proportions of your mantel in relationship to your fireplace are important. Generally, your mantel should extend a minimum of three inches beyond the opening of your fireplace. For reference, if you have a 36-inch fireplace, you’l likely want a mantel width of 48 inches.
How far should a fireplace mantel extend? A mantel should extend a minimum of 3 inches beyond the firebox opening. If the fireplace has facing around the opening, the mantel can also extend 3 or more inches beyond that. Do not guess when sizing the mantel to a room, or the mantel could wind up being too long or too short.
How much should a mantel overhang? Typically, a mantel shelf overhang should extend at least three inches past the fireplace surround. The mantel is usually placed 12 inches above the firebox opening while allowing at least three feet from the mantel shelf to the ceiling.
How far out should a fireplace mantel be? – Related Questions
Is maple ok to burn in a fireplace?
When properly seasoned, it produces long and steady burns in your wood burning stove. Maple can be found throughout the entire continental United States, making it a favorite firewood choice for wood stoves. Check out our beautiful, modern, and easy to use wood stoves!
How wide is a fireplace?
An average fireplace is about 36”x30”. When it comes to the actual dimensions of a fireplace, these can be found in just about any size larger than 24”x24”, all the way up to 48”x32” and higher. The physical size of a fireplace insert is often listed by the width in inches, and they tend to range from about 20” to 60”.
Can you get rid of a gas fireplace?
Gas fireplaces can often be removed in the same way that they have been installed. The steps to install the gas fireplace must be followed in reverse order to remove the fireplace. Professional help will be required for tasks such as disconnecting the gas and electricity supplies.
How does a fireplace gas valve work without power?
A gas fireplace with an intermittent pilot ignition (IPI) valve system will remain operational during a power outage. An IPI valve system is an energy-saving electronic system that utilizes an electrode to ignite your pilot gas. After being sparked by electricity, the pilot flame then lights your main burner gas.
Can you have tv over a natural gas fireplace?
The short answer is – yes. However, to ensure your television isn’t damaged from the heat, care must be taken to ensure heat generated by the fireplace is redirected away from television. There are several ways to do this, such as installing a proper mantel and building an alcove for the television.
How to add wood near a fireplace?
You can choose between letting it be at the bottom, directly in contact with the grate. Or, you could let the kindling and newspaper form the rear end with the wood added last. During the process, wood must only be added when the fire is beginning to smolder.
How much does it cost to run an electric fireplace?
How much does it cost to run an electric fireplace per hour? Based on the national average kilowatt-hour (kWh) rate of 12 cents, a 1,500-watt electric fireplace will cost around 18 cents per hour with all settings at maximum.
How to light pilot on superior gas fireplace?
Press in on the control knob and move it from “off” to the “pilot” position. With your hand still pressing the control knob, wait about five seconds before pressing and repeatedly releasing the igniter button with your other hand. Keep repeating this action with the control knob pressed in until the pilot ignites.
How to cover old brick fireplace with concrete?
Smearing cement over old brick is a great way to makeover an old and dated fireplace without spending a lot of money! You can easily do this in your home, simply have a tile installer come out to float the brick with cement. We used a piece of remnant stone as the hearth which was installed after the cement dried.
How to remove burn marks from fireplace glass?
One clever, all-natural way to clean your fireplace glass is to use a newspaper or paper towel and ash: Take a damp paper towel or newspaper and dip in leftover ashes. Wipe the glass in a circular motion to loosen caked-on soot. Repeat several times or until the soot is lifted.
What is a prefabricated fireplace?
Prefab fireplaces are made in a factory and are most common in newer homes. They first became popular in the 1960s. The inside of a factory-built fireplace is usually made from solid sheets of metal. … Some prefab fireplaces burn wood, some gas, some both.
How to whitewash exterior brick fireplace?
Dish soap: Mix one part mild grease-cutting dish soap and one part salt with just enough water to make a loose paste. Apply to the brick with a clean rag and, using a scrub brush, work the paste into the surface. Let sit for 10 minutes before you rinse.
How to make a proper fireplace fire?
Start by placing two pieces of firewood on the grate in your fireplace. Now crumple newspaper, which is your tinder, and place it between the firewood. Place the kindling on top. Add one or two more pieces of firewood on top of the other logs, and be sure to leave enough room for air to circulate around the logs.
How to light a fireplace for the first time?
Ignite your first fire by using a long-handled lighter or matches to ignite the newspaper and kindling. Use a fireplace poker to stir the sticks as needed until the larger logs ignite. Do not leave a fire unattended. Ensure the fire is fully extinguished before leaving the house or retiring to bed for the night.
Can you mount a led tv over fireplace?
In most cases, you should not install electronics above wood-burning stoves or gas fireplaces and inserts because they produce massive amounts of heat. That heat could severely damage your tv or other electronic devices.
Can you put tile on a brick fireplace?
Can you tile over a brick fireplace? Yes! Tiling over brick (even painted bricked!) is an easy DIY project as long as your brick is in good condition.
How to close fireplace permanently?
How to Permanently Seal Your Fireplace. If you want to seal your fireplace off for good, the easiest way to do so in a hurry is to cut out a foam insulation plug, place it at the bottom of your chimney, and caulk or weatherstrip it in place.
How to clean a brick fireplace for painting?
It’s important to thoroughly clean the brick before you paint it. Use a wire brush and soapy water to scrub the brick and remove any efflorescence (those streaky white deposits) or dirt. If you’re having trouble getting the surface clean, you can apply a mixture of trisodium phosphate (TSP) and water.
What to put under fireplace?
Each fireplace hearth is typically made up of one type of material, and the most commonly found materials used as hearths include:
Does a fireplace need a mantel?
Do You Need A Fireplace Mantel? A fireplace does not need to be furnished with a mantel, but a mantel can enhance the look of a fireplace either as part of fireplace surround or as a standalone mantel shelf.
How much heat loss through fireplace?
According to the Department of Energy, an average home spends approximately $600 per year for heating. What’s more, between 80 and 90 percent of the heat produced by wood burned in an open fireplace is lost up the chimney. This means that for every $100 you spend on firewood, you get only $10 to $20 worth of heat.